#Skyrim console add level Patch#

If, for example, the Enchanting skill is set to level 200, all enchantings will become progressively stronger. Unlike other skills, which behave without any glitch or problem and keep increasing their effects beyond the levelДЎ00, Enchanting shows some problems and glitches. When trying to make minor adjustments to your skill levels via AdvSkill be cautious, as the value of points greatly varies between skills, for example AdvSkill Speechcraft 200 would barely advance the bar by a couple of pixels, but AdvSkill Enchanting 200 would instantly take you to from level 20 to level 86 Enchanting.

Enchanting advanced from level 20 to 26 with only 4 points one level is 00000003 When using AdvSkill on Smithing or Enchanting be very careful as it is extremely easy to overshoot what you're aiming for.

#Skyrim console add level Patch#

Smithing вЂ“ As of the 1.5 patch this has been altered to a much higher value given smithing exp is taken from the value of the item created, 16вЂ“17 is roughly 200.

The closest achieved to whole levels without going much over was: Smithing and Enchanting are not listed above because the AdvSkill adds too much experience to these skills to judge them properly in a single level. The values shown above are the ones required to raise the level of the desired skill by one. Repeat this sequence until you reach your desired level. If this does not obtain the desired skill-level, simply divide the number which you input by the difference in level between the new one and the old one, then multiply by the number of skill levels between the new skill-level and the desired skill-level, and then input this using advskill. In general, multiply the figure below by the desired number of levels required. Enter this using advskill to reach skill-level 50. Then, multiply by the number of level remaining value which is 50 - 43 = 7. Again divide the figure used with advskill, 2862, by the actual number of skill-levels raised, 8 = 357. Now use advskill to raise the skill-level. Multiply this by the difference between the desired skill-level and the new skill-level, (i.e., 50-32 = 18). Then, take the actual number of skill-levels advanced (in this case 7) and divide them by 1075.

Thus resulted in a new skill-level of 32. multiply 25 by 43 (number given below) = 1075, then use player.advskill 'marksman' 1075 to advance the archery skill-level. An easier way to level up quickly, for instance, to skill level 100, is to type in the command and skill and set the value to 100000000.Д®xample: Archer started at skill-level 25 target skill 50, difference 25 skill-levels. This is useful if you want to increase skills by more than one level at a time.

If you have to enter Advskill sneak twenty three times to up a skill, the new value will show advskill sneak 60. Enter the command multiple times until you up a skill up, and use the number of times that command was entered as a multiplier. Note that these values may increase as your skill advances, sneak, lockpicking, and light armor seem to double around the 25вЂ“30 range. Increments of 5000=1 skill boost 10000=2 and so on. The numerical value indicates the '' used to go from level 20 to 21 in each skill. The following are the results for a new character with all skills set to 20.Д®ach skill was set to 20, and then the command player.AdvSkill was used to find the minimum points needed to advance to level 21.

Note that AdvSkill will act as if the skill was gained naturally (causing a progress in leveling), while SetAv does not and allows player to set skills beyond 100.

This is the list of skills verified to work using the AdvSkill and IncPCS commands, as well as SetAv, ForceAv, and ModAv. Please improve this article however you can and remove this notice once finished.